EFFECT OF ROTATION RATES ON DISSOLUTION BEHAVIOR OF LIME IN CaO-FetO-SiO2-MgO SYSTEM.
| Title: | EFFECT OF ROTATION RATES ON DISSOLUTION BEHAVIOR OF LIME IN CaO-Fe |
|---|---|
| Alternate Title: | EFEKAT BRZINE ROTACIJE NA RASTVARANJE KREČA U SISTEMU CaO-FetO-SiO2-MgO. |
| Authors: | Jia, C.1, Mou, Q.-Q.2, Yu, Y.3, Muvunyi, R. A.1, Zhang, M.-X.1, Li, J.-L.1 jli@wust.edu.cn |
| Source: | Journal of Mining & Metallurgy. Section B: Metallurgy. 2024, Vol. 60 Issue 3, p317-327. 11p. |
| Subject Terms: | *ELECTRONIC probes, *MELTING points, *SOLID solutions, *X-ray diffractometers, *SLAG, *OLIVINE, *MASS transfer coefficients, *MASS transfer |
| Abstract (English): | For the converter steelmaking process, incompletely dissolved lime will exist in steel slag in the form of f-CaO, which reduces the utilization rate of metallurgical slag and causes the waste of resources. It is extremely important to reduce the production of f-CaO in steel slag and promote the rapid and sufficient dissolution of lime. This paper is based on the early and middle stages of the converter slag-forming route based on the CaO component. The dissolution rate of lime in four different slags was measured by rotating rod method. The evolution behavior of the lime-slag interface and the change behavior of the lime dissolution rate were studied by X-ray diffractometer and an electron probe micro-analyzer. The experimental results show that CaO-FeO solid solutions and (Ca, Mg, Fe) olivine are formed when lime reacts with molten slag at 1400 ℃. When the FeO content decreases, CaO reacts with the calcium-magnesia-silica to form a high melting point and dense 2CaO·SiO2 layer. In addition, at different rotation rates, a 3CaO·SiO2 phase layer is formed between the CaOFeO solid solution layer and the C2S layer. As the rotation rate increases, the dissolution rate of lime also increases and the mass transfer coefficient reaches the maximum at a rotation rate of 180 rpm. The maximum values are 20.54×10-6 m/s, 7.86×10-6m/s, 9.38×10-6m/s, 5.53×10-6 m/s, respectively. [ABSTRACT FROM AUTHOR] |
| Abstract (Bosnian): | Za proces konvertorske proizvodnje čelika, nepotpuno rastvoreni kreč prisutan je u čeličnoj šljaci u obliku f-CaO, što smanjuje stepen iskorišćenja metalurške šljake i dovodi do rasipanja resursa. Izuzetno je važno smanjiti proizvodnju f-CaO u šljaci i podstaći brzo i potpuno rastvaranje kreča. Ovaj rad se bazira na ranim i srednjim fazama formiranja šljake u konvertoru, uzimajući u obzir CaO komponentu. Brzina rastvaranja kreča u četiri različite šljake ispitana je metodom rotirajuće šipke. Ponašanje na granici kreč-šljaka i promene u brzini rastvaranja kreča proučavani su pomoću rendgenske difrakcije i elektronske sonde mikroanalizatora. Eksperimentalni rezultati pokazuju da se CaO-FeO čvrsta rastvorna faza i (Ca, Mg, Fe) olivin formiraju kada kreč reaguje s tečnom šljakom na 1400℃. Kada se sadržaj FeO smanji, CaO reaguje sa kalcijum-magnezijum-silikatom i formira sloj 2CaO SiO2 visoke tačke topljenja i velike gustine. Pored toga, pri različitim brzinama rotacije, formira se sloj 3CaO SiO2 između sloja CaO-FeO čvrste rastvorne faze i sloja C2S. Kako se brzina rotacije povećava, brzina rastvaranja kreča takođe raste, a koeficijent prenosa mase dostiže maksimum pri brzini rotacije od 180 obrtaja u minuti. Maksimalne vrednosti iznose 20,54×10-6 m/s, 7,86×10-6m/s, 9,38×10-9 m/s i 5,53×10-6 m/s. [ABSTRACT FROM AUTHOR] |
| Copyright of Journal of Mining & Metallurgy. Section B: Metallurgy is the property of Journal of Mining & Metallurgy and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.) | |
| Database: | Academic Search Complete |
| FullText | Links: – Type: pdflink Text: Availability: 0 CustomLinks: – Url: https://resolver.ebsco.com/c/xy5jbn/result?sid=EBSCO:a9h&genre=article&issn=14505339&ISBN=&volume=60&issue=3&date=20240901&spage=317&pages=317-327&title=Journal of Mining & Metallurgy. Section B: Metallurgy&atitle=EFFECT%20OF%20ROTATION%20RATES%20ON%20DISSOLUTION%20BEHAVIOR%20OF%20LIME%20IN%20CaO-FetO-SiO2-MgO%20SYSTEM.&aulast=Jia%2C%20C.&id=DOI:10.2298/JMMB240719026J Name: Full Text Finder (for New FTF UI) (s8985755) Category: fullText Text: Find It @ SCU Libraries MouseOverText: Find It @ SCU Libraries |
|---|---|
| Header | DbId: a9h DbLabel: Academic Search Complete An: 182259126 AccessLevel: 6 PubType: Academic Journal PubTypeId: academicJournal PreciseRelevancyScore: 0 |
| IllustrationInfo | |
| Items | – Name: Title Label: Title Group: Ti Data: EFFECT OF ROTATION RATES ON DISSOLUTION BEHAVIOR OF LIME IN CaO-Fe<subscript>t</subscript>O-SiO<subscript>2</subscript>-MgO SYSTEM. – Name: TitleAlt Label: Alternate Title Group: TiAlt Data: EFEKAT BRZINE ROTACIJE NA RASTVARANJE KREČA U SISTEMU CaO-FetO-SiO2-MgO. – Name: Author Label: Authors Group: Au Data: <searchLink fieldCode="AR" term="%22Jia%2C+C%2E%22">Jia, C.</searchLink><relatesTo>1</relatesTo><br /><searchLink fieldCode="AR" term="%22Mou%2C+Q%2E-Q%2E%22">Mou, Q.-Q.</searchLink><relatesTo>2</relatesTo><br /><searchLink fieldCode="AR" term="%22Yu%2C+Y%2E%22">Yu, Y.</searchLink><relatesTo>3</relatesTo><br /><searchLink fieldCode="AR" term="%22Muvunyi%2C+R%2E+A%2E%22">Muvunyi, R. A.</searchLink><relatesTo>1</relatesTo><br /><searchLink fieldCode="AR" term="%22Zhang%2C+M%2E-X%2E%22">Zhang, M.-X.</searchLink><relatesTo>1</relatesTo><br /><searchLink fieldCode="AR" term="%22Li%2C+J%2E-L%2E%22">Li, J.-L.</searchLink><relatesTo>1</relatesTo><i> jli@wust.edu.cn</i> – Name: TitleSource Label: Source Group: Src Data: <searchLink fieldCode="JN" term="%22Journal+of+Mining+%26+Metallurgy%2E+Section+B%3A+Metallurgy%22">Journal of Mining & Metallurgy. Section B: Metallurgy</searchLink>. 2024, Vol. 60 Issue 3, p317-327. 11p. – Name: Subject Label: Subject Terms Group: Su Data: *<searchLink fieldCode="DE" term="%22ELECTRONIC+probes%22">ELECTRONIC probes</searchLink><br />*<searchLink fieldCode="DE" term="%22MELTING+points%22">MELTING points</searchLink><br />*<searchLink fieldCode="DE" term="%22SOLID+solutions%22">SOLID solutions</searchLink><br />*<searchLink fieldCode="DE" term="%22X-ray+diffractometers%22">X-ray diffractometers</searchLink><br />*<searchLink fieldCode="DE" term="%22SLAG%22">SLAG</searchLink><br />*<searchLink fieldCode="DE" term="%22OLIVINE%22">OLIVINE</searchLink><br />*<searchLink fieldCode="DE" term="%22MASS+transfer+coefficients%22">MASS transfer coefficients</searchLink><br />*<searchLink fieldCode="DE" term="%22MASS+transfer%22">MASS transfer</searchLink> – Name: Abstract Label: Abstract (English) Group: Ab Data: For the converter steelmaking process, incompletely dissolved lime will exist in steel slag in the form of f-CaO, which reduces the utilization rate of metallurgical slag and causes the waste of resources. It is extremely important to reduce the production of f-CaO in steel slag and promote the rapid and sufficient dissolution of lime. This paper is based on the early and middle stages of the converter slag-forming route based on the CaO component. The dissolution rate of lime in four different slags was measured by rotating rod method. The evolution behavior of the lime-slag interface and the change behavior of the lime dissolution rate were studied by X-ray diffractometer and an electron probe micro-analyzer. The experimental results show that CaO-FeO solid solutions and (Ca, Mg, Fe) olivine are formed when lime reacts with molten slag at 1400 ℃. When the FeO content decreases, CaO reacts with the calcium-magnesia-silica to form a high melting point and dense 2CaO·SiO2 layer. In addition, at different rotation rates, a 3CaO·SiO2 phase layer is formed between the CaOFeO solid solution layer and the C2S layer. As the rotation rate increases, the dissolution rate of lime also increases and the mass transfer coefficient reaches the maximum at a rotation rate of 180 rpm. The maximum values are 20.54×10-6 m/s, 7.86×10-6m/s, 9.38×10-6m/s, 5.53×10-6 m/s, respectively. [ABSTRACT FROM AUTHOR] – Name: Abstract Label: Abstract (Bosnian) Group: Ab Data: Za proces konvertorske proizvodnje čelika, nepotpuno rastvoreni kreč prisutan je u čeličnoj šljaci u obliku f-CaO, što smanjuje stepen iskorišćenja metalurške šljake i dovodi do rasipanja resursa. Izuzetno je važno smanjiti proizvodnju f-CaO u šljaci i podstaći brzo i potpuno rastvaranje kreča. Ovaj rad se bazira na ranim i srednjim fazama formiranja šljake u konvertoru, uzimajući u obzir CaO komponentu. Brzina rastvaranja kreča u četiri različite šljake ispitana je metodom rotirajuće šipke. Ponašanje na granici kreč-šljaka i promene u brzini rastvaranja kreča proučavani su pomoću rendgenske difrakcije i elektronske sonde mikroanalizatora. Eksperimentalni rezultati pokazuju da se CaO-FeO čvrsta rastvorna faza i (Ca, Mg, Fe) olivin formiraju kada kreč reaguje s tečnom šljakom na 1400℃. Kada se sadržaj FeO smanji, CaO reaguje sa kalcijum-magnezijum-silikatom i formira sloj 2CaO SiO2 visoke tačke topljenja i velike gustine. Pored toga, pri različitim brzinama rotacije, formira se sloj 3CaO SiO2 između sloja CaO-FeO čvrste rastvorne faze i sloja C2S. Kako se brzina rotacije povećava, brzina rastvaranja kreča takođe raste, a koeficijent prenosa mase dostiže maksimum pri brzini rotacije od 180 obrtaja u minuti. Maksimalne vrednosti iznose 20,54×10-6 m/s, 7,86×10-6m/s, 9,38×10-9 m/s i 5,53×10-6 m/s. [ABSTRACT FROM AUTHOR] – Name: AbstractSuppliedCopyright Label: Group: Ab Data: <i>Copyright of Journal of Mining & Metallurgy. Section B: Metallurgy is the property of Journal of Mining & Metallurgy and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract.</i> (Copyright applies to all Abstracts.) |
| PLink | https://login.libproxy.scu.edu/login?url=https://search.ebscohost.com/login.aspx?direct=true&site=eds-live&scope=site&db=a9h&AN=182259126 |
| RecordInfo | BibRecord: BibEntity: Identifiers: – Type: doi Value: 10.2298/JMMB240719026J Languages: – Code: eng Text: English PhysicalDescription: Pagination: PageCount: 11 StartPage: 317 Subjects: – SubjectFull: ELECTRONIC probes Type: general – SubjectFull: MELTING points Type: general – SubjectFull: SOLID solutions Type: general – SubjectFull: X-ray diffractometers Type: general – SubjectFull: SLAG Type: general – SubjectFull: OLIVINE Type: general – SubjectFull: MASS transfer coefficients Type: general – SubjectFull: MASS transfer Type: general Titles: – TitleFull: EFFECT OF ROTATION RATES ON DISSOLUTION BEHAVIOR OF LIME IN CaO-FetO-SiO2-MgO SYSTEM. Type: main BibRelationships: HasContributorRelationships: – PersonEntity: Name: NameFull: Jia, C. – PersonEntity: Name: NameFull: Mou, Q.-Q. – PersonEntity: Name: NameFull: Yu, Y. – PersonEntity: Name: NameFull: Muvunyi, R. A. – PersonEntity: Name: NameFull: Zhang, M.-X. – PersonEntity: Name: NameFull: Li, J.-L. IsPartOfRelationships: – BibEntity: Dates: – D: 01 M: 09 Text: 2024 Type: published Y: 2024 Identifiers: – Type: issn-print Value: 14505339 Numbering: – Type: volume Value: 60 – Type: issue Value: 3 Titles: – TitleFull: Journal of Mining & Metallurgy. Section B: Metallurgy Type: main |
| ResultId | 1 |